FERROLI WFL4+P7 PELLET ΤΑΞΙΑΡΩΝ. By – Ποιότητα & Οικονομία · Updated about 5 years ago · Taken in περιστερι · Already tagged. Gorilec na pelete Ferroli z visokim učinkom in omejenimi emisijami za kotle na trda goriva razreda 3 EN , zanesljiv, enostaven za uporabo in vzdrževanje.

Author: Mibar Faemuro
Country: Russian Federation
Language: English (Spanish)
Genre: Automotive
Published (Last): 27 January 2013
Pages: 431
PDF File Size: 11.20 Mb
ePub File Size: 13.29 Mb
ISBN: 461-8-87699-412-4
Downloads: 78043
Price: Free* [*Free Regsitration Required]
Uploader: Douramar

In this procedure isno error displayed. When we had our wood burning boiler it was murder when the wind was blowing, the garage was forever filled with smoke and the Vedetta has cured this problem, and now with the new Ferroli the house is toasty warm. Besides these two parameters, t07 is also used, for all power levels!

The price is very tempting. For power level 3, t12 and t13 are used to control the fan t12 and the amount of pellets t You have to look at t This way it uses much more pellet and I would like to make it work as it was, to start a new cycle only when it falls to I am still not giving up on using almond shells but want to make sure first that everything works fine with pellet.

Well, as mentioned before, pellet quality metters most but Ferorli have several issues that I can not relate to pellet. Prova a rimettere le impostazioni di fabbrica per il ventilatore e la coclea. Before playing with that I would like to ask if anyone knows, what decides when are power levels changed?


BRULEUR a Pellet FERROLI Sun P7 | eBay

I keep having problems with pellets. Olive cores were too dirty, bunch of smoke, the dirt would fill up the burner in just hours with the same junk as in your pictures. Otherwise the pellets pipe can become jammed and the burner will stop with A01 error. The quality of pellets is important.

What can be done? You can put it in power modulation mode and then it will change the quantity of pellets so that it matches the power needed. Comunque il Sun P7 in base alla tua ferrlli che giudizio puoi esprime, ti sei trovato bene con questo bruciatore??? Try to reset everything to default values, see the table. So our next job for Spring if not earlier is to purchase the Ferroli boiler, then there should be touch wood no problems.

We did think that perhaps the fan had been installed incorrectly ie wired up wrong but upon further research today, that does not seem likely.

Per Drona, hai provato altri bruciatori a pellet oppure hai usato altri bruciatori a pellet??? Hi Vali, hope all is well with you. It does preventilating O then puts the pellet in the burner and after few moments switches to ventilating again fh.

Feroli I make a fundamental mistake I am not aware.

Ovviamente se hai dei consigli da comunicare ti prego di farlo. This means that t07 is set to 15 seconds and t13 frrroli set to 4.


The purpose is to have enough pellets in the grille so that the heating element is covered. I got good and tall chimney, over ferroil m height. Thank you all for sharing the experience. Not that I care but the guy who brought me olive cores says that I need more air inside boiler. The engineer has been out to see it a couple of times, he has replaced the fan, but can not determine the cause ferroli the overheating, he has replaced the thermostat temperature detection unit, but this has not fixed the problem.


I have seen in manual that there are pins number 9 and 10 E and D on the burner, that give blocking signal and burner deblocade function switch.

You should also look at parameters t05 and t Also you need to clean your chimney periodically. Last year it worked just fine, but I had problem with electronics and I had changed central unit on a burner. Nice explanation of operation, thanks!!! Immediately after ignition the burner would start to load more pellets, trying to reach a normal working cycle. The guy who gave me those olive cores said that he can get them cleaned ……… I am not sure I have the energy to experiment any more, at least at this time.

I am currently experimenting with t17 at