ASTM D is a testing standard for those needing to test fabrics made from Acetate, Acrylic, Cotton, Flax, Nylon, Olefin, Polyester, Rayon, Silk, or Wool. ASTM D Tear strength of fabrics test to determine the resistance to the formation of pills and other related surface changes of textile fabrics using Tongue. Designation: D – 96 (Reapproved ) Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure.
|Published (Last):||21 March 2010|
|PDF File Size:||13.65 Mb|
|ePub File Size:||11.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Description Literature Contact Us Originally introduced inthe latest version was released in Strong fabrics or fabrics made from glass fibers usually require special adaptation to d261 them from ashm in the clamps or being damaged as a result of being gripped in the clamps. Disengage the pawls from the rachet to render them inoperative. The valleys recorded between the peaks have no speci?
In spite of the empirical nature of the reported values, the values are considered to reflect comparative performance of similar fabrics tested and measured in the same way. If any of the preceding modi? Instructions are provided for testing specimens with or without wetting.
A number in parentheses indicates the year of last reapproval. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. Next Checking to see if you are a returning visitor…. The reported value obtained is not directly related to the force required to initiate or start a tear.
It is recognized that some constant-rate-of-traverse-type CRT tensile testing machines continue to be used. Take the specimens to be used for the measurement of the crossmachine direction with the longer dimension parallel to the machine direction.
Consequently, no multi-fabric comparisons were made. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
When specimens are to be tested wet, take the specimens from areas adjacent to the dry test specimens. In this test method, a cut is made in a rectangular specimen, which starts a tear.
As a consequence, these test instruments may be used when agreed upon between the purchaser and the supplier. Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more! Typically for woven fabrics, if a small decrease in force occurs at a time when the force is increasing, it is not considered to peak unless the indicated force exceeds the force required to break a yarn.
For fabrics not readily wet out with water, such as those treated with waterrepellent or water-resistant materials, add a 0.
Email addresses must contain the symbol. Stop the crosshead motion after a total tear of approximately 75 mm 3 in. Take the specimens to be used for the measurement of machine direction with the longer dimension parallel to the cross-machine direction.
If a bias qstm found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias.
Four of the eight specimens were tested on one day, and four specimens were tested on a second day. No known procedure is 2 available that can be used awtm all fabrics to determine the minimum tearing strength.
The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. The force to continue the tear is calculated from asm chart recorders or microprocessor data collection systems.
Summary of Test Method 4. The highest peaks appear to re? Originally published as D — 64 T. If a bias is found, either its cause must be found awtm corrected, or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias. Consequently, r2261 two tensile testers cannot be used interchangeably unless the degree of quantitative correlation has been established between the purchaser and the supplier.
Competent statistical assistance is recommended for the investigation of bias.
ASTM D Tearing Strength of Textile Fabrics – Instron
As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of fabric of the type in question. Bluehill LE for Basic Testing. Onsite Training At Your Facility. Bluehill D226 Software is built from the ground-up for touch interaction and an intuitive user experience.
The resulting data reflects the strength asmt the yarns, fiber bonds, and fiber interlocks, as well as their resistance to tearing.
ASTM D2261 Tearing Strength of Fabrics
The square roots of the components of variance are being reported to express the variability in the appropriate units of measure rather than as the squares of those units of measure. Software for Series Systems. As a consequence, these test instruments may be used when agreed upon between the purchaser and the supplier.
At the same time, the force developed is recorded.